Ice and Water Shield: Where It Goes and How Much You Need

Quick answer: ice and water shield is a self-adhering, rubberized underlayment that seals around nails and stops water that gets under shingles. It goes along the eaves (from the edge to at least 24 in inside the warm wall where code requires it), in valleys, and around chimneys, skylights and walls. Rolls are usually 36 in wide. The original Grace product comes 75 ft long (225 sq ft per roll). The calculator below works out how many rolls you need.

For homeowners checking what a roofer's quote includes, and DIYers adding ice and water shield to their shingle order.

What ice and water shield is

Regular underlayment (felt or synthetic) is nailed down and sheds water that runs over it. Ice and water shield is different in two ways:

That matters where water can sit or back up instead of running off: at the eaves when ice dams form, in valleys where two roof planes pour water together, and at walls and chimneys where flashing meets the roof. In the trade it's also called an ice barrier, leak barrier or self-adhered membrane. "Ice & Water Shield" started as the name of a Grace product that became the generic term. Grace's maker, GCP Applied Technologies, was bought by Saint-Gobain in 2022, and the product is now sold by CertainTeed under the Vycor name. Other brands sell the same type of product under their own names.

Why ice dams make it necessary

In cold climates, heat escaping from the house melts snow on the upper roof. The meltwater runs down and refreezes at the cold overhang, building a ridge of ice. More meltwater pools behind that ice dam and backs up under the shingles. Shingles shed water running downhill, but they can't hold back standing water. Ice and water shield is the layer that keeps that water out of the house.

It doesn't prevent ice dams. Air sealing, insulation and attic ventilation do that. It's the backup for when they form anyway.

Where it goes on a shingle roof

LocationTypical coverageWhy
EavesFrom the roof edge to at least 24 in inside the exterior wall, measured horizontallyIce dams form over the unheated overhang
ValleysA lining at least 36 in wide, centered on the valleyTwo planes concentrate water into one channel
Chimneys and skylightsAround the opening, under the flashingFlashing joints are common leak points
Sidewalls and headwallsA strip where the roof meets the wallBacks up step and wall flashing
Low-slope sectionsOften the full areaWater drains slowly and can be wind-driven under laps
Rakes (optional)A strip along the gable edgesWind-driven rain in some regions

The eave rule is a code requirement in ice-dam areas. For valleys, the building code requires a lining. For closed valleys (shingles run across the valley), that means smooth roll roofing at least 36 in wide, and a self-adhering membrane is an allowed alternative. Most roofers use the membrane. Chimneys, walls and low-slope sections are common practice or come from the shingle manufacturer's instructions, which can be a condition of the warranty.

When code requires it

Under the International Residential Code (IRC), which most US states adopt with local changes, an ice barrier is required at the eaves where there's a history of ice forming along the eaves and causing water backup. Your local jurisdiction says whether that's you, in its climate design table.

States and towns adopt different editions and often amend them. Some require more than 24 in.

The quickest way to know for sure: call your local building department and ask, "Is an ice barrier required at the eaves here, and how far up?" Many cold-climate areas require more than the 24 in minimum.

Ice and water shield calculator

Enter your eaves, valleys and any other areas. The calculator works out how many rows you need at the eaves to reach the required distance inside the wall, then converts everything to rolls. Get eave length and pitch from the roof square footage calculator if you haven't measured yet.

1. Eaves

24 in inside the wall is the common code minimum. Use your local requirement if it's higher. For 8/12 and steeper, the calculator also checks the 36 in along-the-slope minimum.

2. Valleys and other areas

"Other areas" covers chimneys, skylights, sidewall strips and any low-slope section you'll cover fully. Valleys and rakes use one 36 in strip each.

Roll size and laps (match your product)

Defaults match the Grace (now Vycor) data sheet: 36 in × 75 ft, with a 3.5 in side lap between rows. Other brands come in different lengths, so check the label on yours.

3. Price (optional)

How the calculator works

distance up the slope = (overhang + distance inside wall) × pitch multiplier
rows = 1 + ⌈(distance − roll width) ÷ (roll width − lap)⌉
rolls = ⌈((rows × eave + valleys + rakes) ÷ roll length + other areas ÷ roll area) × (1 + waste)⌉

Example: 80 ft of eaves at 6/12 with a 12 in overhang. Reaching 24 in inside the wall means covering 36 in horizontally, which is 36 × 1.118 = 40.2 in up the slope. One 36 in row isn't enough, so you need 2 rows, or 160 ft of membrane. With 75 ft rolls, that's 160 ÷ 75 = 2.13 rolls, or 2.35 with 10% waste: 3 rolls.

Notice that a wider overhang or a steeper pitch can push you from 1 row to 2. That's why "one row at the eaves" isn't always enough to meet code.

Installation tips

Sources: Grace Ice & Water Shield product data sheet; GAF technical bulletin R-152 (cool weather installation); GAF WeatherWatch installation instructions; 2018 IRC R905.1.2 as published by Pennsylvania code officials. States and towns adopt different code editions and amendments, so confirm the rules with your local building department before you install.

Common questions

Is ice and water shield the same as underlayment?

It's a type of underlayment, but a specialized one. It's self-adhering and seals around nails. Regular felt or synthetic underlayment covers the rest of the roof. The shingle calculator estimates that separately.

Should I put ice and water shield on the whole roof?

Usually not on a normal-pitch roof. It costs more than regular underlayment and can trap moisture in some attics. Full coverage is more common on low-slope sections. Ask your roofer or the manufacturer.

Do I need it in a warm climate?

The eave requirement only applies where ice damming is a known problem, so many warm areas don't require it. It's still widely used in valleys and around penetrations, and some manufacturers require it for certain warranties. Check with your local building department.

Complete your shingle order

Add bundles, starter strip, ridge cap, regular underlayment and drip edge in the shingle calculator.

Open the shingle calculator →

Related calculators

Shingle calculator

Bundles, squares, starter and ridge cap.

Calculate →

Roof square footage calculator

Roof area, squares and eave lengths.

Calculate area →

Roof pitch calculator

Pitch in x/12, degrees and percent.

Find your pitch →