How roof pitch is calculated
Pitch compares vertical rise to horizontal run. Roofers in the US always express it per 12 inches of run, so the second number is always 12.
angle = arctan(rise ÷ run)
percent grade = rise ÷ run × 100
area multiplier = √(1 + (rise ÷ run)²)
The area multiplier is what matters for shingles. It converts the flat footprint of a roof into its real sloped surface. Multiply your footprint by it, or use the roof square footage calculator, which does it for you.
Example: a 28 ft wide house with a 7 ft roof rise
Run is half the span: 28 ÷ 2 = 14 ft. Pitch = 7 ÷ 14 × 12 = 6/12. Angle = arctan(0.5) = 26.6°. Every 100 sq ft of footprint becomes 111.8 sq ft of roof.
Roof pitch chart
Each line shows how steep that pitch looks over the same 12 in of run. Hold it up next to your roof's gable end to get a quick visual match, then confirm with a measurement.
Roof pitch table: angle, grade and multiplier
| Pitch | Angle | Grade | Multiplier | 1,000 sq ft footprint |
|---|---|---|---|---|
| 1/12 | 4.8° | 8.3% | 1.003 | 1,003 sq ft |
| 2/12 | 9.5° | 16.7% | 1.014 | 1,014 sq ft |
| 3/12 | 14.0° | 25% | 1.031 | 1,031 sq ft |
| 4/12 | 18.4° | 33.3% | 1.054 | 1,054 sq ft |
| 5/12 | 22.6° | 41.7% | 1.083 | 1,083 sq ft |
| 6/12 | 26.6° | 50% | 1.118 | 1,118 sq ft |
| 7/12 | 30.3° | 58.3% | 1.158 | 1,158 sq ft |
| 8/12 | 33.7° | 66.7% | 1.202 | 1,202 sq ft |
| 9/12 | 36.9° | 75% | 1.250 | 1,250 sq ft |
| 10/12 | 39.8° | 83.3% | 1.302 | 1,302 sq ft |
| 11/12 | 42.5° | 91.7% | 1.357 | 1,357 sq ft |
| 12/12 | 45.0° | 100% | 1.414 | 1,414 sq ft |
| 14/12 | 49.4° | 116.7% | 1.537 | 1,537 sq ft |
| 16/12 | 53.1° | 133.3% | 1.667 | 1,667 sq ft |
| 18/12 | 56.3° | 150% | 1.803 | 1,803 sq ft |
| 24/12 | 63.4° | 200% | 2.236 | 2,236 sq ft |
These values are pure geometry (rounded), so they're the same for every roof and every manufacturer.
How to find your roof pitch
- From the attic (safest): hold a level horizontally against the bottom of a rafter. Mark 12 in along the level, then measure straight up from that mark to the rafter. That's your rise.
- From a ladder at the gable end: hold the level against the rake edge, mark 12 in, and measure vertically to the roof surface.
- From the ground: measure the building span and estimate the ridge height from the top of the wall, then use "total roof rise and building span" above. This is the least precise method.
- Phone app: an inclinometer app gives degrees. Enter them in "angle in degrees" above to convert.
Shed roof pitch
A shed roof has one slope, from a high wall down to a low wall. Its pitch is the difference in wall height divided by the depth of the building:
Example: an 8 ft deep shed with a 96 in high wall and a 72 in low wall rises 24 in over 96 in. That's 24 ÷ 96 × 12 = 3/12.
Going the other way, to design a shed for a target pitch: wall difference = depth × pitch ÷ 12. For an 8 ft deep shed at 4/12, the high wall needs to be 8 × 4 ÷ 12 = 2.67 ft (32 in) taller than the low wall.
Many sheds are built at low pitches to keep the high wall short. That matters if you plan to use shingles, because asphalt shingles have a minimum slope (see below).
Minimum roof pitch for shingles
Asphalt shingles shed water by overlapping. On low slopes, water moves slowly and can be driven up under the laps, so codes and manufacturers set a minimum pitch and require extra underlayment on low slopes.
- Below 2/12: asphalt shingles are not allowed. The IRC (R905.2.2) only permits them on slopes of 2/12 or greater. Use a low-slope system such as a membrane instead.
- 2/12 up to (not including) 4/12: shingles are allowed, but code requires a double layer of underlayment. GAF calls this range "low slope" and also requires double-layer roof deck protection for its shingles there.
- 4/12 and steeper: standard single-layer underlayment. NRCA, the national roofing contractors' association, recommends 4/12 or more for asphalt shingles, so 2/12 to 4/12 is allowed but not ideal.
Other roofing materials have different minimums (slate needs 4/12, for example). See types of roof shingles. Ice dam areas still need an ice barrier at the eaves on any slope. See the ice and water shield guide. Your local code may amend these rules, so check with your building department.
Pitch categories used in this calculator
- Below shingle minimum: under 2/12
- Low slope for shingles: 2/12 to under 4/12 (needs double underlayment)
- Standard: 4/12 to under 8/12
- Steep: 8/12 and up. We put the line here because the 2018 IRC adds a stricter ice barrier rule at 8/12.
There's no single official definition of "low" and "steep". NRCA's glossary calls 3/12 and below "low-slope". OSHA's fall-protection rules call anything steeper than 4/12 a "steep roof", which matters for safety gear on almost every house. The labels above are ours, tied to the shingle rules.
Sources: IRC R905.2.2 and its underlayment rules, as summarized by Jaspector (IRC 2021) and local building departments; GAF on minimum slope; the NRCA glossary; OSHA 29 CFR 1926.500.
Now turn your pitch into a shingle order
Enter each roof section with its pitch and get bundles, starter, ridge cap and underlayment.
Open the shingle calculator →