Roof Square Footage Calculator

Quick answer: roof square footage = footprint (overhangs included) × pitch multiplier. One roofing square = 100 sq ft of roof. A 40 × 30 ft footprint at 6/12 is 1,200 × 1.118 = 1,342 sq ft, or 13.4 squares. You can measure all of it from the ground.

For homeowners checking a roofing quote, DIYers ordering materials, and anyone who needs roof area without climbing up. Pick your roof type below.

Building and overhangs

Measure walls at ground level, then measure how far the roof sticks out past them. Don't know the pitch? Find it with the roof pitch calculator.

How to calculate roof square footage

roof area = footprint × √(1 + (pitch ÷ 12)²)
squares = roof area ÷ 100

The footprint is the roof as seen from directly above, overhangs included. The square root part is the pitch multiplier, which accounts for the extra surface a slope adds. Don't use your home's living-area square footage. It leaves out overhangs, garages and porches, and it ignores slope.

Example: 38 × 28 ft house, 1 ft overhangs, 6/12Result
Footprint: (38 + 2) × (28 + 2)1,200 sq ft
Roof area: 1,200 × 1.1181,342 sq ft
Squares: 1,342 ÷ 10013.4 squares

Gable vs. hip roofs

Gable roofs have two sloped faces and two flat triangular walls at the ends. The rake overhang at those ends adds to the length.

Hip roofs slope on all four sides. If every side has the same pitch, there's a shortcut: the roof area is just the whole footprint times the pitch multiplier. You don't need to measure each triangle and trapezoid separately. A gable and a hip roof over the same footprint and pitch have the same area. What changes is the edges: a hip roof has eaves all the way round, a shorter ridge, and four hips.

For a regular hip roof the calculator also works out the edges with exact geometry:

ridge = footprint length − footprint width
each hip = (footprint width ÷ 2) × √(2 + (pitch ÷ 12)²)

Example: a 40 × 30 ft footprint at 6/12 has a 10 ft ridge and four hips of 15 × √2.25 = 22.5 ft each, 90 ft in total. That's what drives the ridge cap order.

How to measure a roof (from the ground)

Safety first. Every step below can be done from the ground, a ladder at the eave, or the attic. If you go on the roof, use fall protection. Never walk a wet, icy or steep roof (over about 6/12) without proper gear.

1. Sketch the roof from above

Draw a rough bird's-eye view and number every separate flat face. A plain gable has 2, a simple hip has 4. Treat garage, porch and dormer roofs as their own faces. Satellite views are fine for the sketch, but don't trust them for exact sizes.

2. Measure the footprint, including overhangs

Measure each outside wall at ground level. Then measure how far the roof sticks out past the wall at the eaves and at the gable ends. Typical overhangs are 12 to 24 in, but measure yours. Add the overhang on both sides to each wall length.

3. Find the pitch

Hold a level against a rafter in the attic or the rake edge from a ladder, mark 12 in, and measure the vertical rise. Full instructions are on the roof pitch calculator page.

4. Enter it above

Simple gable or hip? Use those tabs. Anything with valleys, wings or dormers? Use "Complex / by section" and enter each face as a rectangle, triangle or trapezoid with its own pitch.

5. Total the edges

Measuring checklist

Got your square footage? Get your shingle order.

Send these numbers straight to the shingle calculator for bundles, starter, ridge cap and underlayment.

Open the shingle calculator →

Related calculators

Shingle calculator

Bundles, squares, starter and ridge cap.

Calculate →

Roof pitch calculator

Pitch in x/12, degrees and percent, plus a pitch chart.

Find your pitch →

Bundles per square

Why it's usually 3 and when it isn't.

Learn more →